Pw3r: /* Steam Container */

2021-12-22T04:25:36Z

Steam Container

← Older revision		Revision as of 04:25, 22 December 2021
Line 255:		Line 255:
	;max-coal-mass		;max-coal-mass
	:Maximum volume of coal.		:Maximum volume of coal.

	~~;maximum-volume~~
	~~:The maximum volume of the piston(in litres).~~

	;minimum-volume		;minimum-volume
	:The minimum volume of the ~~piston~~(in ~~litres~~).		:The 'minimum' volume of the boiler (in millilitres). It's important to note that this is not literally 'empty', but rather the value at which the water gauge will read empty. By default this is 80% of the boiler volume.

			;maximum-volume
			:The 'maximum' volume of the boiler (in millilitres). It's important to note that this is not literally 'full', but rather the value at which the water gauge will read full. By default this is 90% of the boiler volume.

	====Mass Container====		====Mass Container====

Pev at 07:49, 10 November 2012

2012-11-10T07:49:03Z

← Older revision		Revision as of 07:49, 10 November 2012
Line 14:		Line 14:

	A TYPICAL ASSET OF THIS KIND MAY HAVE THE FOLLOWING TAGS:		A TYPICAL ASSET OF THIS KIND MAY HAVE THE FOLLOWING TAGS:
	<font color="red">		<font color="red">kind ''"steam-engine"''</font>
	kind ''"steam-engine"''</font>
	kuid ''kuid''		kuid ''kuid''
	trainz-build ''data''		trainz-build ''data''

Pev: kind steam-engine fixed in sample

2012-11-10T07:48:35Z

kind steam-engine fixed in sample

← Older revision		Revision as of 07:48, 10 November 2012
Line 14:		Line 14:

	A TYPICAL ASSET OF THIS KIND MAY HAVE THE FOLLOWING TAGS:		A TYPICAL ASSET OF THIS KIND MAY HAVE THE FOLLOWING TAGS:
	<font color="red">steam-engine</font>		<font color="red">
			kind ''"steam-engine"''</font>
	kuid ''kuid''		kuid ''kuid''
	trainz-build ''data''		trainz-build ''data''
Line 22:		Line 22:
	category-era ''data''		category-era ''data''
	username ''data''		username ''data''
	~~kind ''data''~~

	<font color="red">flowsize</font>		<font color="red">flowsize</font>

Pev: New page: ==KIND: STEAM-ENGINE== ===Description=== The special engine specification for steam locomotives which defines the detailed performance requirements such as throttle requirements, engine a...

2011-06-08T01:50:56Z

New page: ==KIND: STEAM-ENGINE== ===Description=== The special engine specification for steam locomotives which defines the detailed performance requirements such as throttle requirements, engine a...

New page

==KIND: STEAM-ENGINE==

===Description===
The special engine specification for steam locomotives which defines the detailed performance requirements such as throttle requirements, engine and braking performance, boiler capacity and steam attributes.

===Container Structure===
A well formed steam-engine kind has the following container structure:

[[Image:CCG_steam_engine_dir.jpg]]

See Chapter 7 for an example asset of this kind.

A TYPICAL ASSET OF THIS KIND MAY HAVE THE FOLLOWING TAGS:
steam-engine

kuid ''kuid''
trainz-build ''data''
category-class ''data''
category-region ''data''
category-era ''data''
username ''data''
kind ''data''

flowsize
trainbrakepipe ''data''
epreservoirpipe ''data''
no3pipe ''data''
no4pipe ''data''
auxreservoirvent ''data''
auxreservoir_no3 ''data''
auxreservoir_trainbrakepipe ''data''
autobrakecylindervent ''data''
auxreservoir_autobrakecylinder ''data''
equaliser_mainreservoir ''data''
equaliservent ''data''
equaliserventhandleoff ''data''
equaliserventemergency ''data''
no3pipevent ''data''
no3pipe_mainreservoir ''data''
compressor ''data''
trainbrakepipe_reservoir ''data''
trainbrakepipevent ''data''
no3pipe_autobrakecylinder ''data''
epreservoirpipe_autobrakecylinder ''data''
mainreservoir_ep ''data''
vacuumbrakepipe ''data''
vacuumbrakepipereleasevent ''data''
vacuumbrakepipevent ''data''
vacuumbrakereservoir_vacuumbrakepipe ''data''
vacuumbrakecylinder_vacuumbrakepipe ''data''
highspeedexhauster_vacuumbrakepipe ''data''

volume
scale ''data''
trainbrakepipe ''data''
epreservoirpipe ''data''
no3pipe ''data''
no4pipe ''data''
auxreservoir ''data''
autobrakecylinder ''data''
vacuumbrakepipe ''data''
vacuumbrakereservoir ''data''
vacuumbrakecylinder ''data''
mainreservoir ''data''
equaliser ''data''
independantbrakecylinder ''data''

pressure
scale ''data''
compressor ''data''
mainreservoir ''data''
highspeedexhauster ''data''
brakepipe ''data''
brakeinitial ''data''
brakefull ''data''
indbrakefull ''data''
trainbrakepipe_start ''data''
epreservoirpipe_start ''data''
no3pipe_start ''data''
no4pipe_start ''data''
auxreservoir_start ''data''
autobrakecylinder_start ''data''
vacuumbrakepipe_start ''data''
vacuumbrakereservoir_start ''data''
vacuumbrakecylinder_start ''data''
mainreservoir_start ''data''
equaliser_start ''data''
independantbrakecylinder_start ''data''

mass
scale ''data''
fuel ''data''

motor
resistance ''data''
adhesion ''data''
maxvoltage ''data''
maxspeed ''data''
brakeratio ''data''
max-accel ''data''
max-decel ''data''
axle-count ''data''
surface-area ''data''
moving-friction-coefficient ''data''
air-drag-coefficient ''data''
throttle-notches ''data''

steam
firebox-to-boiler-heat-flow ''data''
firebox-efficiency ''data''
boiler-volume ''data''
minimum-volume ''data''
maximum-volume ''data''
initial-boiler-temperature ''data''
water-injector-rate ''data''
piston-volume-min ''data''
piston-volume-max ''data''
piston-area ''data''
piston-angular-offsets ''data''
firebox-to-boiler-heat-flow-idle ''data''
burn-rate-idle ''data''
boiler-to-piston-flow ''data''
piston-to-atmosphere-flow ''data''
safety-valve-low-pressure ''data''
safety-valve-low-flow ''data''
safety-valve-high-pressure ''data''
safety-valve-high-flow ''data''
max-fire-coal-mass ''data''
max-fire-temperature ''data''
shovel-coal-mass ''data''
burn-rate ''data''
fuel-energy ''data''
firebox-volume ''data''
main-reservoir-volume ''data''
westinghouse-volume ''data''

thumbnails
0
image ''file''
width ''data''
height ''data''

===TAGS AND CONTAINERS===
The following tags are further defined in Chapter 5:

;kuid
:Generated automatically by [[Content Manager]].

;trainz-build
:Automatically set to 2.9 for 2009 assets.

;category-class
:Should be one of the following: "AS" - Steam Loco & Tender, "AT" - Steam Tank.
:See the "Motive Power" section of [[Category Class]].

;category-region
:See [[Category Region]] for a list of valid category-region values.

;category-era
:See [[Category Era]] for a list of valid category-era values.

;username
:Asset username. Though this asset doesn't appear in the Surveyor menu, the username is used to identify the asset in the "Content Manager" and "Content Creator Plus" programs.

;kind
:Must be "steam-engine".

===Additional Containers===
As well as containing all of the common tags and containers detailed in Chapter 5 , the steam-engine kind also contains additional containers and tags that are specialised to the requirements of the kind.

====Steam Container====
The Steam Container stores specialised variables related to steam engines.

The Steam Containers has the following tags:

;boiler-to-piston-flow
:Relative energy.

;boiler-volume
:Physical volume of boiler in litres.

;burn-rate
:Coal consumption rate.

;burn-rate-idle
:Coal consumption rate when idle.

;firebox-efficiency
:Atmosphere leakage. 1.0 = No leakage.

;firebox-to-boiler-heat-flow
:Rate of heat flow from firebox to boiler and viseversa.

;firebox-to-boiler-heat-flow-idle
:Rate of heat flow from firebox to boiler when idle.

;firebox-volume
:Physical volume of firebox in litres.

;fuel-energy
:Relative energy in kilojoules per kilogram of coal.

;main-reservoir-volume
:Main reservoir volume in litres.

;max-fire-coal-mass
:The maximum mass of coal the firebox can take in kilograms.

;max-fire-temperature
:Maximum heat obtainable in degrees K. (Kelvin scale temperature).

;piston-angular-offsets
:Leave this setting.

;piston-volume-min
:The volume of the space in the cylinder ahead of the piston at the end of a full stroke.

;piston-volume-max
:The volume of the space in the cylinder ahead of the piston at the end of a full stroke.

;piston-area
:The cross section of one piston in m2. It is assumed there is one piston only on each side of the locomotive.

;piston-to-atmosphere-flow
:Atmospheric leakage from piston. Nominal hole size.

;safety-valve-low-pressure
:When boiler pressure hits this value in kPa the safety-valve-low-flow release is initiated.

;safety-valve-low-flow
:Lower pressure valve release. Nominal hole size.

;safety-valve-high-pressure
:When boiler pressure hits this value in kPa the safety- valve-low-flow release is initiated.

;safety-valve-high-flow
:Higher pressure valve release. Nominal hole size.

:shovel-coal-mass
;Amount of coal in one shovel load in kg.

;water-injector-rate
:Water injection rate into boiler in litres/second.

;westinghouse-volume
:Westinghouse volume in litres.

;initial-boiler-temperature
:Boiler temperature on loading Trainz.

;max-coal-mass
:Maximum volume of coal.

;maximum-volume
:The maximum volume of the piston(in litres).

;minimum-volume
:The minimum volume of the piston(in litres).

====Mass Container====
The mass container stores information related to fuel consumption. These tags aren't in use and shouldn't generally be used.

The mass container has the following tags:

;scale
:Multiplies fuel mass by given value, not currently in use, generally leave this setting.

;fuel
:Fuel level, not currently in use, generally leave this setting.

====Motor Container====
The Motor Container stores an assortment of values related to motor function, particularly that of DCC.

;resistance
:Power figure for DCC, higher resistance value=less power.

;adhesion
:Adhesion parameter, higher value=greater adhesion.

;maxvoltage
:Generally leave this setting.maxspeed.

;maxspeed
:Maximum speed for DCC, expressed in metres per second.

;brakeratio
:Brake force for pressure reduction.

;max-accel
:Parameters for DCC acceleration & deceleration.

;max-decel
:Parameters for DCC acceleration & deceleration.

;throttle-notches
:Number of throttle notches.

;axle-count
:Resistance - Axle Count.

;surface-area
:Resistance - Surface Area.

;moving-friction-coefficient
:Resistance - Moving friction.

;air-drag-coefficient
:Resistance - Air drag.

====Flowsize Container====
Flowsize settings specify the rate of flow through the pipes. Generally these setting should be left unaltered.

The Flowsize Container has the following tags:

;trainbrakepipe
:Flowsize of the brake pipe.

;epreservoirpipe
:Flowsize of the electric pneumatic braking.

;no3pipe
:Flowsize of the independent brake pipe.

;no4pipe
:Flowsize of the bail pipe.

;auxreservoirvent
:Flowsize of the auxiliary reservoir vent.

;auxreservoir_no3
:Flowsize of the auxiliary independent brake pipe.

;auxreservoir_trainbrakepipe
:Flowsize of the auxiliary reservoir brake pipe.

;autobrakecylindervent
:Flowsize of the automatic brake cylinder vent.

;auxreservoir_autobrakecylinder
:Flowsize of the auxiliary reservoir automatic brake cylinder.

;equaliser_mainreservoir
:Flowsize of the equaliser main reservoir.

;equaliservent
:Flowsize of the equaliser vent.

;equaliserventhandleoff
:Flowsize of the equaliser to the atmosphere when in the "handle off" position.

;equaliserventemergency
:Flowsize of the emergency equaliser vent.

;no3pipevent
:Flowsize of the independent brake pipe.

;no3pipe_mainreservoir
:Flowsize of the independent brake main reservoir.

;compressor
:Flowsize of the compressor.

;trainbrakepipe_reservoir
:Flowsize of the brake pipe reservoir.

;trainbrakepipevent
:Flowsize of the brake pipe vent.

;no3pipe_autobrakecylinder
:Flowsize of the independent automatic brake pipe cylinder.

;epreservoirpipe-autobrakecylinder
:Flowsize of the electro pneumatic automatic brake cylinder reservoir.

;mainreservoir_ep
:Flowsize of the electro pneumatic main reservoir.

;vacuumbrakepipe
:Flowsize of the vacuum brake pipe.

;vacuumbrakepipereleasevent
:Flowsize of the vacuum brake pipe release vent.

;vacuumbrakepipevent
:Flowsize of the vacuum brake pipe vent.

;vacuumbrakereservoir_vacuumbrakepipe
:Flowsize of the vacuum brake pipe reservoir.

;vacuumbrakecylinder_vacuumbrakepipe
:Flowsize of the vacuum brake pipe cylinder.

;highspeedexhauster_vacuumbrakepipe
:Flowsize of the high speed exhauser vacuum brake pipe.

====Volume Container====
The volume container stores information regarding the size of pipes and appliances. Generally these settings should remain unaltered.

The Volume Container has the following tags:

;scale
:Multiplies volume by given value, generally leave this setting.

;trainbrakepipe
:Brake pipe volume.

;epreservoirpipe
:For electro pneumatic braking - not currently in use, generally leave this setting.

;no3pipe
:Independent brake pipe.

;no4pipe
:Bail pipe - not currently in use, generally leave this setting.

;auxreservoir
:Auxiliary reservoir volume.

;autobrakecylinder
:Brake cylinder volume.

;vacuumbrakepipe
:For vacuum braking - not currently in use, generally leave this setting.

;vacuumbrakereservoir
:For vacuum braking - not currently in use, generally leave this setting.

;vacuumbrakecylinder
:For vacuum braking - not currently in use, generally leave this setting.

;mainreservoir
:Main reservoir volume.

;equaliser
:Equalising reservoir volume.

;independantbrakecylinder
:Loco brake cylinder volume.

====Steam-Power Coordinate Container====
This container is a graph, similar to the throttle anddynamic-brake graphs for Velocity incoming, Power multiplier outgoing.

;Coordinate Element
:The steam-power graph provides a speed (m/s) vs power (multiplier) modifier which controls the power output ofthe pistons on a steam train. This is intended to allow fine adjustments to a working steam engine, and should not be used for large adjustments to the performance characteristics, eg.
0 1.0

20 1.1

===THIS KIND SUPPORTS THE FOLLOWING:===

;CONTAINERS
:String Table, Chinese String Table, Czech String Table, Dutch String Table, French String Table, German String Table, Italian String Table, Polish String Table, Russian String Table, Spanish String Table, KUID Table, ObsoleteTable, Thumbnails, Privileges, Extensions, Throttle Power Container, Dynamic Brake Container, Pressure Container, Mass Container, Motor Container, Flowsize Container, Volume Container, Steam container, Steam-Power.

;TAGS
:kuid, trainz-build, category-class, category-region, category-era, username, kind, author, category-keyword, class, contact-email, contact-website, description, description-cn, description-cz, description-de, description-es, description-fr, description-it, description-pl, description-nl, description-ru, license, organisation, username-cn, username-cz, username-de, username-es, username-fr, username-it, username-nl, username-pl, username-ru.

==Return to CCG Index==
[[Content Creator's Guide]]

CCG/Steam-Engine - Revision history

Pw3r: /* Steam Container */

Pev at 07:49, 10 November 2012

Pev: kind steam-engine fixed in sample

Pev: New page: ==KIND: STEAM-ENGINE== ===Description=== The special engine specification for steam locomotives which defines the detailed performance requirements such as throttle requirements, engine a...