ProToolz Yard Template - Revision history

Frogpipe at 15:33, 18 July 2013

2013-07-18T15:33:35Z

← Older revision		Revision as of 15:33, 18 July 2013
Line 1:		Line 1:
	{\|		{\|
	\|-		\|-
			\|[[File:ProTools Yard07.jpg\|right\|200px]]Using the ProToolz Yard template, the following guide will assist in creating parallel tracks (up to 10) for yards.
	\|'''1)''' All tools are accessed by selecting 3DTrains in the Region window of the Objects tab.		\|-
			\|[[File:ProTools Yard01.jpg\|right\|200px]]'''1)''' All tools are accessed by selecting 3DTrains in the Region window of the Objects tab. ''Does not apply to all versions, if your version has no region window, use Filter and 3dtrains''

	Start by selecting and dropping in the ProToolz Yard template from the Objects tab. The tool requires two ProToolz Yard templates to work. Place one in the left side of your view, and another on the right. We'll worry about placement later.		Start by selecting and dropping in the ProToolz Yard template from the Objects tab. The tool requires two ProToolz Yard templates to work. Place one in the left side of your view, and another on the right. We'll worry about placement later.
Line 8:		Line 9:
	Note: For angled trackage, you'll need to match up the two templates at their proper angles prior to adding in track.		Note: For angled trackage, you'll need to match up the two templates at their proper angles prior to adding in track.
	\|-		\|-
	\|'''2)''' Select the track tool, and lay-in a section to any of the inside points of the template. String each of these tracks from one template to the other.		\|[[File:ProTools Yard02.jpg\|right\|200px]]'''2)''' Select the track tool, and lay-in a section to any of the inside points of the template. String each of these tracks from one template to the other.
			\|-
			\|[[File:ProTools Yard03.jpg\|right\|200px]]'''3)''' Determine the number of tracks required for your yard (in this case, we chose 10 tracks). Keep in mind that you may want to use the outside tracks as mainlines and yard leads (using 10 slots of the template, this creates 1 mainline, two leads, and 7 yard tracks). However, you can also make these all yard tracks, and simply add-in the mainline and yard leads as needed.
	\|-		\|-
	\|'''3)''' ~~Determine~~ the ~~number of tracks required for your yard (in this case~~, ~~we chose 10 tracks). Keep in mind that you may want to use the outside tracks as mainlines and yard leads (using 10 slots of~~ the template~~, this creates 1 mainline, two leads, and 7 yard tracks). However, you can also make these all yard tracks, and simply add-in~~ the ~~mainline and yard leads as needed~~.		\|[[File:ProTools Yard04.jpg\|right\|200px]]'''4)''' Grabbing one of the 3DTrains yellow blocks, move the ProToolz Yard template to the desired location.
	\|-		\|-
	\|'''4)''' ~~Grabbing one of the 3DTrains yellow blocks~~, ~~move~~ the ~~ProToolz Yard~~ template to the ~~desired location~~.		\|[[File:ProTools Yard05.jpg\|right\|200px]]'''5)''' Once in place, delete the template from the baseboard.
	\|-		\|-
	\|'''5)''' ~~Once~~ in ~~place~~, ~~delete~~ the ~~template from~~ the ~~baseboard~~.		\|[[File:ProTools Yard06.jpg\|right\|200px]]'''6)''' Add-in your Track Markers, switch points, and connect the mainline to the yard.
	\|-		\|-
	\|'''~~6)''' Add-in your Track Markers, switch points, and connect the mainline to the yard.~~		\|[[File:ProTools Yard07.jpg\|right\|200px]]'''You're Done!'''
	You're Done!

	And there you have it. A dead-straight multi-track yard, and the whole process took less than a minute! As Rob at Auran would say: "'''''...and that's all there is to it!'''''"		And there you have it. A dead-straight multi-track yard, and the whole process took less than a minute! As Rob at Auran would say: "'''''...and that's all there is to it!'''''"
	\|}		\|}

Frogpipe at 15:24, 18 July 2013

2013-07-18T15:24:44Z

← Older revision		Revision as of 15:24, 18 July 2013
Line 19:		Line 19:
	You're Done!		You're Done!

	And there you have it. A dead-straight multi-track yard, and the whole process took less than a minute! As Rob at Auran would say: "...and that's all there is to it!"		And there you have it. A dead-straight multi-track yard, and the whole process took less than a minute! As Rob at Auran would say: "'''''...and that's all there is to it!'''''"
	\|}		\|}

Frogpipe: Created page with "{| |- |'''1)''' All tools are accessed by selecting 3DTrains in the Region window of the Objects tab. Start by selecting and dropping in the ProToolz Yard template from the ..."

2013-07-18T15:23:47Z

Created page with "{| |- |'''1)''' All tools are accessed by selecting 3DTrains in the Region window of the Objects tab. Start by selecting and dropping in the ProToolz Yard template from the ..."

New page

{|
|-

|'''1)''' All tools are accessed by selecting 3DTrains in the Region window of the Objects tab.

Start by selecting and dropping in the ProToolz Yard template from the Objects tab. The tool requires two ProToolz Yard templates to work. Place one in the left side of your view, and another on the right. We'll worry about placement later.

Note: For angled trackage, you'll need to match up the two templates at their proper angles prior to adding in track.
|-
|'''2)''' Select the track tool, and lay-in a section to any of the inside points of the template. String each of these tracks from one template to the other.
|-
|'''3)''' Determine the number of tracks required for your yard (in this case, we chose 10 tracks). Keep in mind that you may want to use the outside tracks as mainlines and yard leads (using 10 slots of the template, this creates 1 mainline, two leads, and 7 yard tracks). However, you can also make these all yard tracks, and simply add-in the mainline and yard leads as needed.
|-
|'''4)''' Grabbing one of the 3DTrains yellow blocks, move the ProToolz Yard template to the desired location.
|-
|'''5)''' Once in place, delete the template from the baseboard.
|-
|'''6)''' Add-in your Track Markers, switch points, and connect the mainline to the yard.
You're Done!

And there you have it. A dead-straight multi-track yard, and the whole process took less than a minute! As Rob at Auran would say: "...and that's all there is to it!"
|}