ProToolz Switch Template

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 Using these templates you will be able to create perfectly aligned switches / points / turnouts in minutes.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 1) All tools are accessed by selecting 3DTrains in the Region window of the Objects tab. Does not apply to all versions, if your version has no region window, use Filter and 3dtrains Start by selecting and dropping in one of the ProToolz templates from the Objects tab. You may move and rotate it into place, or start building the switch right away, or you can build the switch anywhere on the baseboard, and move/rotate it into place whenever you're ready!

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 2) Select the track tool, and lay-in a section to any of the inside points of the template. You'll note in the picture that I'm placing the spline point away from the center of the switch template. This is so that the splines won't jump to an adjacent spline.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 3) Because you cannot connect the same track piece within the template, you'll need to add-in another section and then link it the template point. The previous example in Step 2 becomes clear.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 4) Repeat the process for the lead adding in a spline away from the center of the template. Add in another to the switch point as in Step 3.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 5) Using the delete spline tool, remove the extra spline points in the center of each new track section.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 6) OK, now you can either continue to build - adding track to any of the outside points of the ProToolz template, or you can grab the big yellow 3DTrains box and drag to the desired location. If you haven't yet done so, move/rotate the entire switch into place. Tip: Use the straight edges of the yellow 3DTrains box to align the switch. Set it against the mainline near where you'll be placing the switch.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 7) Once the outer points have been connected (and you're satisfied with the placement of the switch), delete the entire jig.

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 8) Now we need to fill the gaps left by the ProToolz template. Connect the tracks of the mainline and/or branch line to the relevant outer points of your new switch:

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 9) You're almost home, but not there yet. The spline from the turnout will curve to meet its connecting piece, so we'll need to straighten the track: Select the Straighten Tool from the Track Tab and click on each piece of track (except the 1st lead spline).

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 10) Add-in a switch lever, and then move the lever towards the switch point. Also, you can rename the lever at this time if you like (use the "?" icon).

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 You're Done! And there you have it. A razor-sharp turnout, and the whole process took less than a minute! As Rob at Auran would say: "...and that's all there is to it!"

Error creating thumbnail: /bin/bash: line 1: /usr/bin/convert: No such file or directory Error code: 127 Uses Right and left versions of the ProTools templates consist of #4's, #5's, #6's, and #8's. Since Trainz allows for a larger space than what you might build at home in a model layout, use the following as a guide when selecting the appropriate switch size: #4 - Logging, Industrial, Streetcar, etc. #5 - Industrial and Branch Lines #6 - Branch Lines and Mainline #8 - Mainline